Browsing by Author "Kasedde, H."

Now showing 1 - 5 of 5
  • Thumbnail Image
    Item
    Characterization And Pre-Leaching Effect On The Peels Of Predominant Cassava Varieties In Uganda For Production Of Activated Carbon
    (Current Research in Green and Sustainable Chemistry, 2021) Kayiwa, R.; Kasedde, H.; Lubwama, M.; Kirabira, J.B.
    Activated Carbon (AC) remains a key material for both industrial and domestic applications. The aim of this work was to characterize the peels of predominant cassava varieties grown in Uganda for production of AC. The selected varieties were; NASE 1, NASE 3, NASE 14, NASE 19, NAROCAS 1, and NAROCAS 2 due to more guaranteed raw material availability and potential for sustainability for AC production. The peels were characterized through proximate and ultimate analysis, bulk density, water-binding capacity, and lignocellulosic composition. Pre-leaching was done using NaOH of 1–4% w/v concentrations on two representative peel varieties. The dry basis (db) values of ash content, volatile matter and fixed carbon percentages of the peel varieties ranged from 1.93 to 4.36%, 77.93–81.93% and 13.78–15.34%, respectively. The ash content values were below 5% and hence may not necessitate pre-leaching to remove any ash forming agents. The dry basis char yield from the peels at 400 ​°C is in the range of 27.76–31.09%, qualifying them for AC production. The lignin, cellulose and hemicellulose compositions are in the ranges 9.0–16.0%, 5.5–15.0%, and 41.0–65.0%, respectively. The varieties with higher cellulosic content may be more suitable for highly porous AC production. Pre-leaching showed no remarkable reduction in the ash content but increased the volatile matte and char yield at low NaOH concentrations. Predominant Ugandan cassava peel varieties have potential for production of AC with alkaline pretreatment required in applications where high char yields are required.
  • Thumbnail Image
    Item
    Experimental Evaluation Of Rice Husk Ash For Applications In Geopolymer Mortars
    (Journal of Bioresources and Bioproducts, 2021) Ogwang, G.; Olupot, P.W.; Kasedde, H.; Menya, E.; Storz, H.; Kiros, Y.
    Rice husks obtained from upland and lowland rice varieties were characterized for composition and content of ash. Each of the rice husk varieties was fired at temperatures of 600, 800 and 900 °C for a soaking period of 3 h. The resultant rice husk ash was analyzed for oxide composition and crystallinity using X-ray fluorescence and diffraction techniques, respectively. The generated amorphous ash with the highest silica content, together with metakaolin, aggregate, water, and an alkaline activator was employed to formulate geo-polymer mortar prisms according to the standard EN 196–1. Results showed that the content of ash in the varieties ranged from 18.3% to 28.6% dry basis. Out of this, 89 wt%–96 wt% was silica, with amorphous and crystalline forms of silica obtained at 600 °C and 900 °C, respectively, regardless of the rice variety. However, at 800 °C, the silica in the generated ash exhibited both amorphous and crystalline forms. The amorphous ash generated at 600 °C was used in formulation of geopolymer mortars. Compressive and flexural strength of the formulated mortar after 7 days of curing was 1.5 and 1.3 MPa, respectively. These results reveal the firing protocol to form pozzolanic ash, with potential applications in mortar production.
  • Thumbnail Image
    Item
    Mesoporous activated carbon yielded from pre‑leached cassava peels
    (Bioresources and Bioprocessing, 2021) Kayiwa, R.; Kasedde, H.; Lubwama, M.; Kirabira, J. B.
    The search for alternatives to fossil-based commercial activated carbon (AC) continues to reveal new eco-friendly potential precursors, among which is agricultural waste. The key research aspect in all these endeavors is empirical ascertainment of the core properties of the resultant AC to suit a particular purpose. These properties include: yield, surface area, pore volume, and the active surface groups. It is therefore pertinent to have process conditions controlled and tailored towards these properties for the required resultant AC. Pre-leaching cassava peels with NaOH followed by KOH activation and carbonization at holding temperatures (780 °C) above the melting point of K (760 °C) yielded mesoporous activated carbon with the highest surface area ever reported for cassava peel-based AC. The carbonization temperatures were between 480 and 780 °C in an activation–carbonization stepwise process using KOH as the activator at a KOH:peel ratio of 5:2 (mass basis). A 42% maximum yield of AC was realized along with a total pore volume of 0.756 cm3g− 1 and BET surface area of 1684 m2g− 1. The AC was dominantly microporous for carbonization temperatures below 780 °C, but a remarkable increase in mesopore volume (0.471 cm3g− 1) relative to the micropore volume (0.281 cm3g− 1) was observed at 780 °C. The Fourier transform infrared (FTIR) spectroscopy for the pre-treated cassava peels showed distortion in the C–H bonding depicting possible elaboration of more lignin from cellulose disruption by NaOH. A carboxylate stretch was also observed owing to the reaction of Na+ ions with the carboxyl group in the raw peels. FTIR showed possible absorption bands for the AC between 1425 and 1712 cm− 1 wave numbers. Besides the botanical qualities of the cassava peel genotype used, pre-leaching the peels and also increasing holding activation temperature above the boiling point of potassium enabled the modified process of producing highly porous AC from cassava peel. The scanning electron microscope (SEM) and transmission electron microscope (TEM) imaging showed well-developed hexagonal pores in the resultant AC and intercalated K profile in the carbon matrices, respectively.
  • Thumbnail Image
    Item
    Occurrence and toxicological assessment of selected active pharmaceutical ingredients in effluents of pharmaceutical manufacturing plants and wastewater treatment plants in Kampala, Uganda
    (Water Practice & Technology, 2022) Kayiwa, R.; Kasedde, H.; Lubwama, M.; Kirabira, J. B.; Kayondo, Timothy
    There is an increasing eco-toxicological risk associated with pharmaceuticals globally. The prevalence of six active pharmaceutical ingredients (APIs) was studied in effluents of three pharmaceutical manufacturing plants (PMPs) and two wastewater treatment plants (WWTPs) in Kampala, Uganda to ascertain the removal potentials for APIs. The APIs include atenolol, losartan, carbamazepine, sulfamethoxazole, clarithromycin, and diclofenac. The APIs were extracted using solid-phase extraction cartridges and concentrations were analyzed using a liquid chromatography-mass spectrometer system. The concentration ranges of the APIs were
  • Thumbnail Image
    Item
    Phase Diagram Modelling of a Multicomponent Aqueous Solution of Katwe Salt Lake, Uganda
    (International Conference on Environmental Science and Technology, 2019) Lwanyaga, J.D.; Kasedde, H.; Kirabira, J.B;
    A methodology is developed to compute the phase diagram of a hexary system and to determine the mineral precipitation sequence upon removal of water. The methodology is applied to construct the phase diagram and precipitation sequence of the system ( in water. The thermodynamic model chosen is the Extended UNIQUAC. A 3D grid is constructed in order to solve this model in MATLAB. On the basis of this grid, a 3D phase diagram is calculated and a Jänecke projection is obtained. The precipitation sequence due to evaporation is calculated thus obtaining the coordinates of the solution along this path as well as the order of precipitation. The numerical model is also able to calculate all these steps for temperatures 0-110°C. In addition, the number of ions and the composition of the system can be varied in order to model other elective systems. The obtained results are well suited to be used for the design of sustainable salt extraction processes for both Sea and Lake brines.